Danh mục tiêu chuẩn Quốc tế ASTM công bố trong tháng 12 năm 2018

Đăng ngày: 14:10 07-12-2018

ASTM Quốc tế, tên giao dịch tiếng Anh là ASTM International, là một tổ chức tiêu chuẩn quốc tế thực hiện phát triển và xuất bản các tiêu chuẩn kỹ thuật đồng thuận tự nguyện cho loạt các vật liệu, sản phẩm, hệ thống và dịch vụ

Danh mục tiêu chuẩn IEC ban hành tháng 12:

New Approved ASTM Standards

A1098/A1098M - Standard Specification for Welded Austenitic, Ferritic, Martensitic and Duplex Stainless Steel Boiler, Superheater, Condenser, and Heat Exchanger Tubes with Textured Surface(s) has been revised (with title change) to A1098/A1098M-18 developed by Committee A01.10, ASTM BOS Volume 01.01.


A354 - Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners has been editorially changed, available as A354-17e2 developed by Committee F16.02, ASTM BOS Volume 01.09.


A369/A369M - Standard Specification for Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service has been revised to A369/A369M-18a developed by Committee A01.10, ASTM BOS Volume 01.01.


A924/A924M - Standard Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process has been revised to A924/A924M-18 developed by Committee A05.11, ASTM BOS Volume 01.06.


C167 - Standard Test Methods for Thickness and Density of Blanket or Batt Thermal Insulations has been revised to C167-18 developed by Committee C16.32, ASTM BOS Volume 04.06.


C307 - Standard Test Method for Tensile Strength of Chemical-Resistant Mortar, Grouts, and Monolithic Surfacings has been revised to C307-18 developed by Committee D01.46, ASTM BOS Volume 06.02.


C413 - Standard Test Method for Absorption of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes has been revised to C413-18 developed by Committee D01.46, ASTM BOS Volume 06.02.


C531 - Standard Test Method for Linear Shrinkage and Coefficient of Thermal Expansion of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes has been revised to C531-18 developed by Committee D01.46, ASTM BOS Volume 06.02.


C579 - Standard Test Methods for Compressive Strength of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes has been revised to C579-18 developed by Committee D01.46, ASTM BOS Volume 06.02.


C580 - Standard Test Method for Flexural Strength and Modulus of Elasticity of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concreteshas been revised to C580-18 developed by Committee D01.46, ASTM BOS Volume 06.02.


C909 - Standard Practice for Dimensions of a Modular Series of Refractory Brick and Shapes has been revised to C909-18 developed by Committee C08.92, ASTM BOS Volume 15.01.


D2156 - Standard Test Method for Smoke Density in Flue Gases from Burning Distillate Fuels has been reapproved, available as D2156-09(2018) developed by Committee D02.E0, ASTM BOS Volume 05.01.


D2422 - Standard Classification of Industrial Fluid Lubricants by Viscosity System has been reapproved, available as D2422-97(2018) developed by Committee D02.L0.11, ASTM BOS Volume 05.01.


D2718 - Standard Test Methods for Structural Panels in Planar Shear (Rolling Shear) has been revised to D2718-18 developed by Committee D07.03, ASTM BOS Volume 04.10.


D2890 - Standard Test Method for Calculation of Liquid Heat Capacity of Petroleum Distillate Fuels has been reapproved, available as D2890-92(2018) developed by Committee D02.04.0K, ASTM BOS Volume 05.01.


D4057 - Standard Practice for Manual Sampling of Petroleum and Petroleum Products has been reapproved, available as D4057-12(2018) developed by Committee D02.02, ASTM BOS Volume 05.02.


D483 - Standard Test Method for Unsulfonated Residue of Petroleum Plant Spray Oils has been reapproved, available as D483-04(2018) developed by Committee D02.06, ASTM BOS Volume 05.01.


D5443 - Standard Test Method for Paraffin, Naphthene, and Aromatic Hydrocarbon Type Analysis in Petroleum Distillates Through 200 °C by Multi-Dimensional Gas Chromatography has been reapproved, available as D5443-14(2018) developed by Committee D02.04.0L, ASTM BOS Volume 05.02.


D6199 - Standard Practice for Quality of Wood Members of Containers and Pallets has been revised to D6199-18a developed by Committee D10.12, ASTM BOS Volume 15.10.


D6457 - Standard Specification for Extruded and Compression Molded Rod and Heavy-Walled Tubing Made from Polytetrafluoroethylene (PTFE) (Withdrawn 2018) has been withdrawn, with no replacement. D1710 developed by Committee D20.15, ASTM BOS Volume 08.03.


D6923 - Standard Test Method for Evaluation of Engine Oils in a High Speed, Single-Cylinder Diesel Engine—Caterpillar 1R Test Procedure has been revised to D6923-18 developed by Committee D02.B0, ASTM BOS Volume 05.03.


D7829 - Standard Guide for Sediment and Water Determination in Crude Oil has been reapproved, available as D7829-13(2018) developed by Committee D02.02, ASTM BOS Volume 05.05.


D8227 - Standard Test Method for Determining the Coefficient of Friction of Synchronizer Lubricated by Mechanical Transmission Fluids (MTF) Using a High-Frequency, Linear-Oscillation (SRV) Test Machine is a new standard, now available. D8227-18 developed by Committee D02.L0, ASTM BOS Volume 05.05.


D87 - Standard Test Method for Melting Point of Petroleum Wax (Cooling Curve) has been reapproved, available as D87-09(2018) developed by Committee D02.10.0A, ASTM BOS Volume 05.01.


D893 - Standard Test Method for Insolubles in Used Lubricating Oils has been reapproved, available as D893-14(2018) developed by Committee D02.06, ASTM BOS Volume 05.01.


D95 - Standard Test Method for Water in Petroleum Products and Bituminous Materials by Distillation has been reapproved, available as D95-13(2018) developed by Committee D02.02, ASTM BOS Volume 05.01.


E2738 - Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) for Computed Radiography (CR) Test Methods has been revised to E2738-18 developed by Committee E07.11, ASTM BOS Volume 03.04.


E2849 - Standard Practice for Professional Certification Performance Testing has been revised to E2849-18 developed by Committee E36.80, ASTM BOS Volume 14.02.


F17 - Standard Terminology Relating to Primary Barrier Packaging has been revised to F17-18a developed by Committee F02.50, ASTM BOS Volume 15.10.


F1805 - Standard Test Method for Single Wheel Driving Traction in a Straight Line on Snow- and Ice-Covered Surfaces has been revised to F1805-18 developed by Committee F09.20, ASTM BOS Volume 09.02.


F2430 - Standard Specification for Bearing, Roller, Needle: Assembly (Thick Outer Race) has been reapproved, available as F2430-04(2018) developed by Committee F34.04, ASTM BOS Volume 01.09.


F2431 - Standard Specification for Ring Bearing, Inner: For Needle Roller Bearing with Thick Outer Ring has been reapproved, available as F2431-04(2018) developed by Committee F34.04, ASTM BOS Volume 01.09.


F2444 - Standard Practice for Damage Prevention of Bearings, and Bearing Components Through Proper Handling Techniques has been reapproved, available as F2444-04(2018) developed by Committee F34.03, ASTM BOS Volume 01.09.


New ASTM Work Items

WK65989 - Standard Specification for Seamless and Welded Titanium and Titanium Alloy Tubes for Condensers and Heat Exchangers is a work item revision to existing standard B338-17


WK65990 - Standard Practice for Calibration of Laboratory Volumetric Apparatus is a work item revision to existing standard E542-01(2012)


WK65991 - Standard Classification for Serviceability of an Office Facility for Thermal Environment and Indoor Air Conditions is a work item revision to existing standard E2320-04(2018)


WK65992 - Standard Test Method for Determining Density of Structural Lightweight Concrete is a work item revision to existing standard C567/C567M-14


WK65999 -Practice for Impact Shear Pin Brinell Portable Hardness Testing


WK66000 - Standard Specification for Metal Injection Molded (MIM) Materials is a work item revision to existing standard B883-17


WK66001 - Standard Specification for Materials for Ferrous Powder Metallurgy (PM) Structural Parts is a work item revision to existing standard B783-13


WK66002 - Standard Specification for Copper Rod for Electrical Purposes is a work item revision to existing standard B49-17


WK66003 - Standard Specification for Copper Rod for Electrical Purposes is a work item revision to existing standard B49-17


WK66004 - Standard Specification for Structural Steel Shapes is a work item revision to existing standard A992/A992M-11(2015)


WK66005 - Standard Specification for High-Strength Low-Alloy Structural Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance is a work item revision to existing standard A588/A588M-15


WK66006 - Standard Specification for Structural Steel for Ships is a work item revision to existing standard A131/A131M-14


WK66007 - Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service is a work item revision to existing standard A106/A106M-18


WK66008 - Standard Specification for Steel Bars Subject to Restricted End-Quench Hardenability Requirements is a work item revision to existing standard A914/A914M-16


WK66009 - Standard Specification for Liquid-Applied Silicone Coating Used in Spray Polyurethane Foam Roofing Systems is a work item revision to existing standard D6694/D6694M-15


WK66010 - Standard Test Method for Corrosion Test for Engine Coolants in Glassware is a work item revision to existing standard D1384-05(2012)


WK66011 -Practice for Stress Liquid Chemicals to be Reused in the Manual Disinfection of Heat sensitive Medical Devices


WK66020 - Standard Test Method for Resistance to Abrasion of Resilient Floor Coverings Using an Abrader with a Grit Feed Method is a work item revision to existing standard F510/F510M-14


WK66021 - Standard Test Method for Equilibrium Moisture of Coal at 96 to 97 Percent Relative Humidity and 30 °C is a work item revision to existing standard D1412/D1412M-17a


WK66022 - Standard Practice for Conducting a Ruggedness Evaluation or Screening Program for Test Methods for Construction Materials is a work item revision to existing standard C1067-12


WK66023 - Standard Practices for Force Verification of Testing Machines is a work item revision to existing standard E4-16


WK66024 - Standard Practices for Force Verification of Testing Machines is a work item revision to existing standard E4-16


WK66025 - Standard Guide for Hand Hole Design in Corrugated Boxes is a work item revision to existing standard D6804-02(2015)


WK66026 - Standard Test Method for Determining the Water Washout Characteristics of Lubricating Greasesis a work item revision to existing standard D1264-18

 (nguồn astm.org)


Cùng chuyên mục