Tiêu chuẩn quốc tế
Số hiệu
Standard Number
ASTM B581-02(2008)
Năm ban hành 2008
Publication date
Tình trạng
A - Còn hiệu lực
Status |
Tên tiếng Anh
Title in English Standard Specification for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Rod
|
Chỉ số phân loại Quốc tế (ICS)
By field |
Số trang
Page 4
Giá:
Price Liên hệ / Contact us
|
Phạm vi áp dụng
Scope of standard 1.1 This specification covers rod of Ni-Cr-Fe-Mo-Cu alloys (UNS N06007, N06975, N06985, N06030, and N08031)* as shown in Tables 1-2, for use in general corrosive service. 1.2 The following products are covered under this specification: 1.2.1 Rods 5/16 to ¾ in. (7.94 to 19.05 mm) excl in diameter, hot- or cold-finished, solution annealed and pickled or mechanically descaled. 1.2.2 Rods ¾ to 3½ in. (19.05 to 88.9 mm) incl in diameter, hot- or cold-finished, solution annealed, ground or turned. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. TABLE 1 Chemical Requirements ElementComposition Limits, % Alloy N06007Alloy N06975Alloy N06985Alloy N06030Alloy N08031Nickel remainderA47.0-52.0remainderAremainderA30.0-32.0 Chromium 21.0-23.5 23.0-26.0 21.0-23.5 28.0-31.526.0-28.0 Iron 18.0-21.0remainderA18.0-21.013.0-17.0remainderAMolybdenum5.5-7.5 5.0-7.0 6.0-8.0 4.0-6.030.-7.0 Copper 1.5-2.5 0.70-1.20 1.5-2.5 1.0-2.41.0-1.4 Manganese 1.0-2.0 1.0 max 1.0 max 1.5 max2.0 max Cobalt, max2.5... 5.0 max 5.0 max...Carbon, max0.050.030.015 max 0.03 max0.015 Tungsten 1.0 max... 1.5 max 1.5-4.0... Silicon, max1.0 1.0 1.0 max 0.8 max0.3 Phosphorus, max 0.04 0.03 0.04 max 0.04 max0.020 Sulfur, max 0.03 0.03 0.03 max 0.02 max0.010 Columbium + tantalum 1.75-2.50 ... 0.50 max 0.30-1.50... Titanium ... 0.7-1.5... ......Nitrogen0.15-0.25............ A See 13.1.1. TABLE 2 Permissible Variations in Diameter and Out-of-Roundness of Rods Specified Diameter, in. (mm) Permissible Variations, in. (mm) Diameter Out-of-Roundness, max + − Hot-Finished, Annealed, and Descaled Rods5/16 to 7/16 (7.94 to 11.11), incl0.012 (0.305)0.012 (0.305)0.018 (0.457)Over 7/16 to 5/8(11.11 to 15.87), incl 0.014 (0.355)0.014 (0.355)0.020 (0.508)Over 5/8 to ¾ (15.87 to 19.05), excl0.016 (0.406)0.016 (0.406)0.024 (0.610)Hot-Finished, Annealed, and Ground or Turned Rods ¾ to 3½ (19.05 to 88.9), incl0.010 (0.254)00.008 (0.203)
|