Tiêu chuẩn quốc tế

• Số hiệu / Standard Number: ASTM B860-09
• Năm ban hành / Publication date: 2009
• Tình trạng / Status: A - Còn hiệu lực
• Tên tiếng Anh / Title in English: Standard Specification for Zinc Master Alloys for Use in Hot Dip Galvanizing
• Số trang / Page: 3
• Phạm vi áp dụng / Scope of standard: 1.1 This specification covers zinc master alloys which are used in hot dip galvanizing for the purpose of adjusting the concentration of certain alloying elements in the molten zinc bath. Table 1 covers the chemical composition of these materials which include six master alloys of zinc-aluminum (brightener) and one master alloy of zinc-antimony. ASTM Common UNS Type A-190/10 Zn/Al High PurityZ30750 Type A-290/10 Zn/Al Low PurityZ31710Type A-395/5 Zn/Al High PurityZ30503 Type A-495/5 Zn/Al Low PurityZ31510Type A-596/4 Zn/Al High Purity...Type A-696/4 Zn/AlLow Purity...Type S-190/10 Zn/Sb Z557101.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use. TABLE 1 Chemical Requirements Composition, % (Range or Maximum Value)A Type A-190 % Zinc-10 % Aluminum (90/10 Zn/Al)High PurityType A-290 % Zinc-10 % Aluminum (90/10 Zn/Al)Low PurityType A-395 % Zinc-5 % Aluminum (95/5 Zn/Al)High PurityType A-495 % Zinc-5 % Aluminum (95/5 Zn/Al)Low PurityType A-596 % Zinc-4 % Aluminum (96/4 Zn/Al)High PurityType A-696 % Zinc-4 % Aluminum (96/4 Zn/Al)Low PurityType S-190 % Zinc-10 % Antimony (90/10 Zn/Sb)UNSBType A-1 90/10 Zn/Al Z30750Type A-2 90/10 Zn/Al Z31710Type A-3 95/5 Zn/Al Z30503Type A-4 95/5 Zn/Al Z31510 Type A-5 96/4 Zn/Al ZXXXXXType A-6 96/4 Zn/Al ZXXXXXType S-1 90/10 Zn/Sb Z55710Fe0.05 max0.15 max0.05 max0.15 max0.05 max0.15 max0.03 maxPb0.005 max0.4 max0.005 max0.4 max0.0005 max0.4 max0.015 maxCd0.004 max...0.004 max...0.004 max...0.003 maxCu0.035 max0.5 max0.035 max0.5 max0.035 max0.5 max0.003 maxMg............0.06 max0.06 maxSn0.003 max...0.003 max...0.003 max...0.01 maxAs..................0.015 maxAl9.5-10.59.5-10.54.5-5.54.5-5.54.0-4.54.0-4.5...SbC..................9.5-10.5Others, Total0.01 max0.25 max0.01 max0.25 max0.01 max0.25 max0.03 maxZnDRemainderRemainderRemainderRemainderRemainderRemainderRemainder A The following applies to all specified limits in this table: For purposes of determining conformance with this specification, an observed value obtained from analysis shall be rounded off to the nearest unit in the last right-hand place of figures used in expressing the limiting value, in accordance with the rounding method of Practice E 29. B UNS numbers in conformance with Practice E 527. C Chemical method under development. D For information only. Quantitative determination of this element is not required. Zinc is assumed to be the difference between 100 % and the sum of those elements listed above.