Tra cứu Tiêu chuẩn quốc tế
Tìm thấy 73948 kết quả.
Searching result
| 29901 |
IEC 61181:2007
Mineral oil-filled electrical equipment - Application of dissolved gas analysis (DGA) to factory tests on electrical equipment |
| 29902 |
IEC 61188-5-3:2007
Printed boards and printed board assemblies - Design and use - Part 5-3: Attachment (land/joint) considerations - Components with gull-wing leads on two sides |
| 29903 |
IEC 61188-5-4:2007
Printed boards and printed board assemblies - Design and use - Part 5-4: Attachment (land/joint) considerations - Components with J leads on two sides |
| 29904 |
IEC 61188-5-5:2007
Printed boards and printed board assemblies - Design and use - Part 5-5: Attachment (land/joint) considerations - Components with gull-wing leads on four sides |
| 29905 |
IEC 61188-5-8:2007
Printed board and printed board assemblies - Design and use - Part 5-8: Attachment (land/joint) considerations - Area array components (BGA, FBGA, CGA, LGA) |
| 29906 |
IEC 61189-3:2007
Test methods for electrical materials, printed boards and other interconnection structures and assemblies - Part 3: Test methods for interconnection structures (printed boards) |
| 29907 |
IEC 61193-2:2007
Quality assessment systems - Part 2: Selection and use of sampling plans for inspection of electronic components and packages |
| 29908 |
|
| 29909 |
IEC 61196-1-203:2007
Coaxial communication cables - Part 1-203: Environmental test methods - Test for water penetration of cable |
| 29910 |
IEC 61223-3-2:2007
Evaluation and routine testing in medical imaging departments - Part 3-2: Acceptance tests - Imaging performance of mammographic X-ray equipment |
| 29911 |
IEC 61290-10-2:2007
Optical amplifiers - Test methods - Part 10-2: Multichannel parameters - Pulse method using a gated optical spectrum analyzer |
| 29912 |
IEC 61290-10-4:2007
Optical amplifiers - Test methods - Part 10-4: Multichannel parameters - Interpolated source subtraction method using an optical spectrum analyzer |
| 29913 |
IEC 61290-7-1:2007
Optical amplifiers - Test methods - Part 7-1: Out-of-band insertion losses - Filtered optical power meter method |
| 29914 |
IEC 61300-2-22:2007
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-22: Tests - Change of temperature |
| 29915 |
IEC 61300-2-49:2007
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-49: Tests - Connector installation test |
| 29916 |
IEC 61300-2-50:2007
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-50: Tests - Fibre optic connector proof test with static load - Singlemode and multimode |
| 29917 |
IEC 61300-2-51:2007
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-51: Tests - Fibre optic connector test for transmission with applied tensile load - Singlemode and multimode |
| 29918 |
IEC 61300-3-42:2007
Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-42: Examinations and measurements - Attenuation of single mode alignment sleeves and or adaptors with resilient alignment sleeves |
| 29919 |
IEC 61310-1:2007
Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| 29920 |
IEC 61310-2:2007
Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
