Tra cứu Tiêu chuẩn quốc tế
Tìm thấy 104041 kết quả.
Searching result
| 36721 |
|
| 36722 |
BS EN ISO 2128:2010Anodizing of aluminium and its alloys. Determination of thickness of anodic oxidation coatings. Non-destructive measurement by split-beam microscope Anodizing of aluminium and its alloys. Determination of thickness of anodic oxidation coatings. Non-destructive measurement by split-beam microscope |
| 36723 |
BS EN ISO 2171:2010Cereals, pulses and by-products. Determination of ash yield by incineration Cereals, pulses and by-products. Determination of ash yield by incineration |
| 36724 |
BS EN ISO 22391-2:2010Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) Part 2: Pipes Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) Part 2: Pipes |
| 36725 |
BS EN ISO 22391-3:2010Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) Part 3: Fittings Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) Part 3: Fittings |
| 36726 |
BS EN ISO 22391-5 / A1:2010Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) Part 5: Fitness for purpose of the system Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) Part 5: Fitness for purpose of the system |
| 36727 |
BS EN ISO 22391-5:2010Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) Part 5: Fitness for purpose of the system Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) Part 5: Fitness for purpose of the system |
| 36728 |
BS EN ISO 225:2010Fasteners. Bolts, screws, studs and nuts. Symbols and descriptions of dimensions Fasteners. Bolts, screws, studs and nuts. Symbols and descriptions of dimensions |
| 36729 |
BS EN ISO 2307:2010Fibre ropes. Determination of certain physical and mechanical properties Fibre ropes. Determination of certain physical and mechanical properties |
| 36730 |
|
| 36731 |
BS EN ISO 276:2010Binders for paints and varnishes. Linseed stand oil. Requirements and methods of test Binders for paints and varnishes. Linseed stand oil. Requirements and methods of test |
| 36732 |
BS EN ISO 277:2010Binders for paints and varnishes. Raw tung oil. Requirements and methods of test Binders for paints and varnishes. Raw tung oil. Requirements and methods of test |
| 36733 |
BS EN ISO 2825:2010Spices and condiments. Preparation of a ground sample for analysis Spices and condiments. Preparation of a ground sample for analysis |
| 36734 |
BS EN ISO 2858:2010End-suction centrifugal pumps (rating 16 bar). Designation, nominal duty point and dimensions End-suction centrifugal pumps (rating 16 bar). Designation, nominal duty point and dimensions |
| 36735 |
BS EN ISO 286-1:2010Geometrical product specifications (GPS). ISO code system for tolerances on linear sizes. Basis of tolerances, deviations and fits Geometrical product specifications (GPS). ISO code system for tolerances on linear sizes. Basis of tolerances, deviations and fits |
| 36736 |
BS EN ISO 2871-1:2010Surface active agents. Detergents. Determination of cationic-active matter content. High-molecular-mass cationic-active matter Surface active agents. Detergents. Determination of cationic-active matter content. High-molecular-mass cationic-active matter |
| 36737 |
BS EN ISO 2871-2:2010Surface active agents. Detergents. Determination of cationic-active matter content. Cationic-active matter of low molecular mass (between 200 and 500) Surface active agents. Detergents. Determination of cationic-active matter content. Cationic-active matter of low molecular mass (between 200 and 500) |
| 36738 |
BS EN ISO 3369:2010Impermeable sintered metal materials and hardmetals. Determination of density Impermeable sintered metal materials and hardmetals. Determination of density |
| 36739 |
BS EN ISO 3386-1:1997+A1:2010Polymeric materials, cellular flexible. Determination of stress-strain characteristics in compression. Low-density materials Polymeric materials, cellular flexible. Determination of stress-strain characteristics in compression. Low-density materials |
| 36740 |
BS EN ISO 3386-2:1998+A1:2010Flexible cellular polymeric materials. Determination of stress-strain characteristics in compression. High-density materials Flexible cellular polymeric materials. Determination of stress-strain characteristics in compression. High-density materials |
