Tra cứu Tiêu chuẩn quốc tế

BS ISO 4715:1978

Essential oils. Quantitative evaluation of residue on evaporation

Essential oils. Quantitative evaluation of residue on evaporation

BS L 167:1978

Specification for close toleranced sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8)

Specification for close toleranced sheet and strip of aluminium-coated aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (Cu 4.4, Mg 0.5, Si 0.8, Mn 0.8)

BS L 168:1978

Specification for bars and extruded sections of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (not exceeding 200 mm diameter or minor sectional dimension) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8)

Specification for bars and extruded sections of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (not exceeding 200 mm diameter or minor sectional dimension) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8)

BS MA 78:1978

Specification for aluminium shore gangways

Specification for aluminium shore gangways

BS QC 160000-1:1987*IEC 60255-7:1978

Harmonized system of quality assessment for electronic components. Electrical relays. Generic specification: electromechanical all-or-nothing relays. Test and measurement procedures

Harmonized system of quality assessment for electronic components. Electrical relays. Generic specification: electromechanical all-or-nothing relays. Test and measurement procedures

BS QC 221400:1997*IEC 60169-9:1978

Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 3 mm (0,12 in) with screw coupling. Characteristic impedance 50 ohms (Type SMC)

Radio-frequency connectors. RF coaxial connectors with inner diameter of outer conductor 3 mm (0,12 in) with screw coupling. Characteristic impedance 50 ohms (Type SMC)

BS SP 164:1978

Specification for design and performance requirements for turnlock, stud-type panel fasteners (metric series)

Specification for design and performance requirements for turnlock, stud-type panel fasteners (metric series)

BS T 76:1978

Specification for chromium-molybdenum steel tube (770 MPa) (weldable)

Specification for chromium-molybdenum steel tube (770 MPa) (weldable)

DIN 12785 Supplement 1:1978

Laboratory glassware; special purpose laboratory thermometers, additional remarks

Laboratory glassware; special purpose laboratory thermometers, additional remarks

DIN 68100 Supplement 1:1978

Tolerances for linear measure and angular dimensions in the wood-working and wood-processing industry; change of dimensions due to the influence of moisture parallel to the grain of solid wood, radial and tangential to the grain of spruce, fir, larch, pine and oregon-pine

Tolerances for linear measure and angular dimensions in the wood-working and wood-processing industry; change of dimensions due to the influence of moisture parallel to the grain of solid wood, radial and tangential to the grain of spruce, fir, larch, pine and oregon-pine

DIN 68100 Supplement 2:1978

Tolerances for linear measure and angular dimensions in the wood-working and wood-processing industry; change of dimensions due to the influence of moisture radial and tangential to the grain of afrormosia, afzelia, ekki, beech, oak, ash, iroko, khaya (african mahagony), macore and yellow meranti

Tolerances for linear measure and angular dimensions in the wood-working and wood-processing industry; change of dimensions due to the influence of moisture radial and tangential to the grain of afrormosia, afzelia, ekki, beech, oak, ash, iroko, khaya (african mahagony), macore and yellow meranti

DIN 68100 Supplement 3:1978

Tolerances for linear measure and angular dimensions in the wood-working and wood-processing industry; change of dimensions due to the influence of moisture, radial and tangential to the grain of red-meranti, muhuhu, niangon, walnut, aspen (poplar), utile, teak, elm and wenge (panga panga)

Tolerances for linear measure and angular dimensions in the wood-working and wood-processing industry; change of dimensions due to the influence of moisture, radial and tangential to the grain of red-meranti, muhuhu, niangon, walnut, aspen (poplar), utile, teak, elm and wenge (panga panga)

DIN 68100 Supplement 4:1978

Tolerances for linear measure and angular dimensions in the wood-working and wood-processing industry; change of dimensions due to the influence of moisture in the direction of thickness, width and length of particle-board, plywood and fibreboard

Tolerances for linear measure and angular dimensions in the wood-working and wood-processing industry; change of dimensions due to the influence of moisture in the direction of thickness, width and length of particle-board, plywood and fibreboard

HD 368 S1:1978

Direct acting recording electrical measuring instruments and their accessoriesIEC 60258:1968 + A1:1976

Direct acting recording electrical measuring instruments and their accessoriesIEC 60258:1968 + A1:1976

ISO 1155:1978

Information processing - Use of longitudinal parity to detect errors in information messages

ISO 140-1:1978

Acoustics -- Measurement of sound insulation in buildings and of building elements -- Part 1: Requirements for laboratories

ISO 140-2:1978

Acoustics -- Measurement of sound insulation in buildings and of building elements -- Part 2: Statement of precision requirements

ISO 140-3:1978

Acoustics -- Measurement of sound insulation in buildings and of building elements -- Part 3: Laboratory measurements of airborne sound insulation of building elements

ISO 140-4:1978

Acoustics -- Measurement of sound insulation in buildings and of building elements -- Part 4: Field measurements of airborne sound insulation between rooms

ISO 140-5:1978

Acoustics -- Measurement of sound insulation in buildings and of building elements -- Part 5: Field measurements of airborne sound insulation of facade elements and facades